3D Printer Part Auto Leveling Kit, BL-Touch Auto Leveling Upgraded Kit for 3D Printer for CR-10/for CR-10SPRO/ENDER-3(As Pictures)

3D Printer Part Auto Leveling Kit, BL-touch Auto Leveling Upgraded Kit for 3D Printer for CR-10/for CR-10SPRO/ENDER-3
Features:
An auto leveling sensor for 3D Printer based on open-source
Simple, high-quality, smart and precise
Used for 3D Printer for CR-10/for CR-10SPRO/ENDER-3

Item type: Auto Press Bed Leveling Kit
Material: Plastic
Color: As pictures.

Packing includes:
1 set of Leveling Kit

Notes:
1. Due to the different monitor and light effect, the actual color of the item might be slightly different from the color showed on the pictures. Thank you!
2. Please allow 1-3cm measuring deviation due to manual measurement.

Product Features

  • Portable: Small size and simple structure, easy to use. Can be compatible with all bed materials such as glass, wood, wood, plastic, acrylic etc.
  • Optimized structure: Larger Build Size: It is a small and technology-intensive one. Build size can be set larger than other existing auto bed leveling sensor. Uses existing RC Servo motor signal intactly, so just plug on the same pins after removing servo motor.
  • 3D Touches is an auto leveling sensor for 3D Printers that can precisely measure the tilt of your print surface. It can greatly improve the printing precision of your 3D Printer.
  • An auto leveling sensor for 3D Printer based on open-source.
  • Packing includes: 1 set of Leveling Kit . Item type: Auto Press Bed Leveling Kit;

Visit The Website For More Information…

WINSINN 3D Printer Controller Kit For Arduino Mega 2560 Uno R3 Starter Kits + RAMPS 1.6 Upgraded Mosfet + 5Pcs DRV8825 Stepper Motor Driver + LCD 12864 for Arduino Reprap


Ramps 1.6 board:

-Ramps 1.6 is optimized and launched based on Ramps 1.4 & Ramps 1.5. The Struture almost same as Ramps 1.5 , the difference is Ramps 1.6 have new 2pin connectors,which more simple and convenient to connect,also will not be burnt easily. And Ramps 1.6 have a good Heatsink above MOS tube in order to give a better function to heat dissipation. Beside, the Power of Ramps 1.6 is more larger than Ramps 1.5, the largest power will be up to or 270W, and Ramps 1.5 just can be up to 200W, or smaller than 200W.

DRV8825 Driver:

-Suitable for driving below 8.2V ~ 45V 2.5A stepper motor
-Six different stepping resolutions: full, half, 1/4,1/8,1/16,1/32
-Adjustable potentiometer can adjust the maximum output current, resulting in higher step rate
-Automatic current decay mode detection / selection
-Thermal shutdown circuit, undervoltage lockout, crossover current protection
-Ground short-circuit protection and load short-circuit protection

Mega 2560 R3:

-Operating Voltage: 5V
-Input Voltage (recommended):7-12V
-Input Voltage (limits):6-20V
-Digital I/O Pins:54 (of which 14 provide PWM output)
-Analog Input Pins:16
-DC Current per I/O Pin:40 mA
-DC Current for 3.3V Pin:50 mA
-Flash Memory:256 KB of which 4 KB used by bootloader
-SRAM:8 KB
-EEPROM:4 KB

—————————————————————————————————————

Package include:
►1 x RAMPS 1.6 Board
►1 x Mega 2560 R3 Board
►1 x 12864 LCD Display Controller
►1 x LCD Smart Adapter
►5 x DRV8825 Stepper

———————————————————————————————————————

►Note:
►We offer the best products and services, if there has any problems, you can tell us anytime. Thank you:))

Product Features

  • ✔️DRV8825 driver board widely used in 3D printers and small CNC machines. It is upgrade of A4988, 4-layer PCB for improved heat dissipation and decrease chip resistance. It suitable for driving below 8.2V ~ 45V 2.5A stepper motor, And had Six different stepping resolutions: full, half, 1/4 ,1/8, 1/16, 1/32.
  • ✔️12864 LCD: The intelligent controller includes an SD card reader, rotary encoders and a 20-character × 4 line LCD display. You can easily connect it to your RAMPS 1.6 board using “smart adapter” included. This panel connect your RAMPS 1.6, you do not need your computer, your SD card intelligent controller power supply. All further operations, such as calibration, the axis movement can be done only with a rotary encoder intelligent controller.
  • ✔️This kit includes a complete set of the most common and useful components that can be used by all tech-savvy people out there to build their own printer controller. A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • ✔️Product Warranty: WINSINN are devoted to offer premium quality products to all cherished customers. Meanwhile supply 60 days money back guarantee and 24 months warranty. If there are any questions, please feel free to contact us, WINSINN Customer Service Team will spare no efforts to assist with you within 24 hours.
  • ✔️Ramps 1.6 is optimized and launched based on Ramps 1.4 & Ramps 1.5. The Struture almost same as Ramps 1.5 , the difference is Ramps 1.6 have new 2pin connectors,which more simple and convenient to connect,also will not be burnt easily. And Ramps 1.6 have a good Heatsink above MOS tube in order to give a better function to heat dissipation. Beside, the Power of Ramps 1.6 is more larger than Ramps 1.5, the largest power will be up to or 270W, and Ramps 1.5 just can be samller than 200W.

Click Here If You Need More Detailed Info…

Upgraded Ender 3 Extruder, Vibury MK8 Extruder Aluminum Drive Feed Replacement 3D Printer Extruders Kit for Creality Ender 3/3 Pro CR-10, CR-10S, CR-10 S4, CR-10 S5 Right Hand Version

Metal Upgrade extruder for Creality Ender 3/3 Pro, CR-10, CR-10S, CR-10 S4, CR-10 S5

Upgraded Replacement Aluminum Drive Feed MK8 Extruder 3D Printer Extruders Kit [Right Hand]
This modified MK8 Extruder has a filament guide tube, all screws, spare drive gear, and upgraded Bowden tube fitting, for Ender 3 ender 3 pro CR 10 3D Printer.

Features:
● This extruder set is great for Creality 3D Ender 3 ender 3 pro CR-10. For all 1.75 mm filament [Right Hand]
● Made of high quality metal material.
● Easy and convenient to use.
● With high quality and durable performance.
● Main material: Metal

●Upgrade Replacement for Creality CR10 Series:CR-10 Series, CR-10 S4, CR-10 S5, CR-10 Mini, CR-10S, CR-10 Plus, This durable aluminum extruder frame works more stable than plastic parts.
● Bowden Extrusion are supported: It comes with a nema stepper motor mount, works great on TEVO Tarantula i3,Anycubic Kossel i3 Mega, Flsun i3,MP Select and other bowden extrusion 3d printers as well.
● Direct Extrusion are supported: This upgrade parts can also work as MK8 extruder frame with some screws replacements.
● Recommend filament materials: PLA/ABS/Wood/TPU/PTEG,40 Teeth drive gear moves the 1.75mm filament very smoothly.

Note: There are many small parts in the package, for safety, please keep away from your child.

Included:
1x Creality 3D – Extruder Upgrade Kit [Right Hand]

Product Features

  • Upgrade Aluminum Replacement: Full metal aluminum alloy. MK8 extruder drive feed kit, can replace acrylic parts of Creality 3D Printers CR-10 Series Ender 3/3 Pro CR-10 S4, CR-10 S5, CR-10 Mini, CR-10S, CR-10 Plus.
  • Easy to Install: All you do is unbolt the old original plastic extruder and screw in the new “Metal Extruder”, then it is ready to print. Suitable for 1.75mm filament 3D printer MK8 bowden extruder frame.
  • Stable and Durable: Full metal aluminum alloy, DIY kit and you need to assemble by yourself. Our MK8 extruder hot end include all the necessary screws & parts needed to directly replace your old original weak Creality plastic extruder.
  • Advantages: The advantages of our extruder drive is you have better stronger pressure pushing the filament into the printer nozzle and so will improve on the printers’ performance. Our extruder kits have an adjustable bolt so that you can adjust the pressure of the extruder gear as needed.
  • Buy with confidence: For 12 months after the date of purchase, we take care of all quality-related issues with a Money Back Or Products Exchange Guarantee.

Click Here If You Need More Detailed Info…

Creality 3D Printer Part BL Touch Bed Leveling Sensor, Auto Press Bed Spare Leveling Upgraded Kit for 3D Printer CR-10/for CR-10SPRO/ENDER-3(as The Pictures Shown)

Creality 3D Printer Part BL Touch Bed Leveling Sensor, Auto Press Bed Spare Leveling Upgraded Kit For 3D Printer CR-10/for CR-10SPRO/ENDER-3

Features:
An auto leveling sensor for 3D Printer based on open-source
Simple, high-quality, smart and precise
Used for 3D Printer for CR-10/for CR-10SPRO/ENDER-3

Item type: Auto Press Bed Leveling Kit
Material: Plastic
Color: As pictures.

Packing includes:
1 set of Leveling Kit

Notes:
1. Due to the different monitor and light effect, the actual color of the item might be slightly different from the color showed on the pictures. Thank you!
2. Please allow 1-3cm measuring deviation due to manual measurement.

Product Features

  • An auto leveling sensor for 3D Printer based on open-source.
  • 3D Printer Accessories, 3D Printer Part BLTouch Auto Press Bed Leveling Kit Used for 3D Printer for CR-10/for CR-10SPRO/ENDER-3 2. Auto leveling position sensor, upgrade your self-assembly 3D
  • Leveling Kit Spare Easy Install Replacement Precise Auto Press Bed Accessories Sensor Smart 3d Printer Part For CR-10/Ender-3
  • Utilizzato per stampante 3D per CR-10 / per CR-10S PRO / ENDER-3
  • Simple, high-quality, smart and precise.

Visit The Website For More Information…