WINSINN 3D Printer Controller Kit For Arduino Mega 2560 Uno R3 Starter Kits + RAMPS 1.6 Upgraded Mosfet + 5Pcs DRV8825 Stepper Motor Driver + LCD 12864 for Arduino Reprap


Ramps 1.6 board:

-Ramps 1.6 is optimized and launched based on Ramps 1.4 & Ramps 1.5. The Struture almost same as Ramps 1.5 , the difference is Ramps 1.6 have new 2pin connectors,which more simple and convenient to connect,also will not be burnt easily. And Ramps 1.6 have a good Heatsink above MOS tube in order to give a better function to heat dissipation. Beside, the Power of Ramps 1.6 is more larger than Ramps 1.5, the largest power will be up to or 270W, and Ramps 1.5 just can be up to 200W, or smaller than 200W.

DRV8825 Driver:

-Suitable for driving below 8.2V ~ 45V 2.5A stepper motor
-Six different stepping resolutions: full, half, 1/4,1/8,1/16,1/32
-Adjustable potentiometer can adjust the maximum output current, resulting in higher step rate
-Automatic current decay mode detection / selection
-Thermal shutdown circuit, undervoltage lockout, crossover current protection
-Ground short-circuit protection and load short-circuit protection

Mega 2560 R3:

-Operating Voltage: 5V
-Input Voltage (recommended):7-12V
-Input Voltage (limits):6-20V
-Digital I/O Pins:54 (of which 14 provide PWM output)
-Analog Input Pins:16
-DC Current per I/O Pin:40 mA
-DC Current for 3.3V Pin:50 mA
-Flash Memory:256 KB of which 4 KB used by bootloader
-SRAM:8 KB
-EEPROM:4 KB

—————————————————————————————————————

Package include:
►1 x RAMPS 1.6 Board
►1 x Mega 2560 R3 Board
►1 x 12864 LCD Display Controller
►1 x LCD Smart Adapter
►5 x DRV8825 Stepper

———————————————————————————————————————

►Note:
►We offer the best products and services, if there has any problems, you can tell us anytime. Thank you:))

Product Features

  • ✔️DRV8825 driver board widely used in 3D printers and small CNC machines. It is upgrade of A4988, 4-layer PCB for improved heat dissipation and decrease chip resistance. It suitable for driving below 8.2V ~ 45V 2.5A stepper motor, And had Six different stepping resolutions: full, half, 1/4 ,1/8, 1/16, 1/32.
  • ✔️12864 LCD: The intelligent controller includes an SD card reader, rotary encoders and a 20-character × 4 line LCD display. You can easily connect it to your RAMPS 1.6 board using “smart adapter” included. This panel connect your RAMPS 1.6, you do not need your computer, your SD card intelligent controller power supply. All further operations, such as calibration, the axis movement can be done only with a rotary encoder intelligent controller.
  • ✔️This kit includes a complete set of the most common and useful components that can be used by all tech-savvy people out there to build their own printer controller. A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • ✔️Product Warranty: WINSINN are devoted to offer premium quality products to all cherished customers. Meanwhile supply 60 days money back guarantee and 24 months warranty. If there are any questions, please feel free to contact us, WINSINN Customer Service Team will spare no efforts to assist with you within 24 hours.
  • ✔️Ramps 1.6 is optimized and launched based on Ramps 1.4 & Ramps 1.5. The Struture almost same as Ramps 1.5 , the difference is Ramps 1.6 have new 2pin connectors,which more simple and convenient to connect,also will not be burnt easily. And Ramps 1.6 have a good Heatsink above MOS tube in order to give a better function to heat dissipation. Beside, the Power of Ramps 1.6 is more larger than Ramps 1.5, the largest power will be up to or 270W, and Ramps 1.5 just can be samller than 200W.

Click Here If You Need More Detailed Info…

Elegoo UNO Project Super Starter Kit with Tutorial for Arduino

Elegoo Inc. is a professional manufacturer and exporter that is concerned with the design, development production and marketing of arduino, 3d printers, raspberry pi and STM32.
Our Dream is to make the best price and best quality produce for customers.
So we would like to receive your valuable suggestions for our products and we can improve them for you.

Warning Tip:
The input voltage of Elegoo Power Supply Module is 6.5v – 9v (DC) via 5.5mm x 2.1mm plug . Please DO NOT over charge it otherwise it will burn your board and chips.

Applicable Age : 12+
Note:To use Elegoo starter kits requires basic electronic knowledge. If the user has no experience, it would be better to have someone lead and teach them while studying.

Component listing:
1pcs UNO R3 Controller Board
1pcs LCD1602 Module ( with pin header)
1pcs Breadboard Expansion Board
1pcs Power Supply Module
1pcs Joystick Module
1pcs IR Receiver
1pcs Servo Motor (SG90)
1pcs Stepper Motor
1pcs ULN2003 Stepper Motor Driver Board
1pcs Ultrasonic Sensor
1pcs DHT11 Temperature and Humidity Module
1pcs 9V Battery with DC
1pcs 65 Jumper Wire
1pcs USB Cable
1pcs Active Buzzer
1pcs Passive Buzzer
1pcs Potentiometer
1pcs 5V Relay
1pcs Breadboard
1pcs Remote
1pcs Tilt Switch
5pcs Button (small)
1pcs 1 digit 7-segment Display
1pcs 4 digit 7-segment Display
5pcs Yellow LED
5pcs Blue LED
5pcs Green LED
5pcs Red LED
1pcs RGB LED
2pcs Photoresistor
1pcs Thermistor
2pcs Diode Rectifier (1N4007)
2pcs NPN Transistor (PN2222)
1pcs IC 74HC595
30pcs Resistor
10pcs Female-to-male Dupont Wire

Product Features

  • Free PDF tutorial(more than 22 lessons) and clear listing in a nice package
  • The most economical way to starting Arduino programming for those beginners who are interested
  • Lcd1602 module with pin header (not need to be soldered by yourself)
  • This is the upgraded starter kits with power supply module, 9V battery with dc
  • High quality kite with uno R3, 100 percent compatible with Arduino uno R3

Detailed Information available on our Homepage…

3D Digital Printer Pen Starter Kit, 3D Printing Pen for 3D Printing, Drawing, Model Building and Craft Works Comes With a Starter Pack Of 3 x ABS Filement & “For FREE” 3 x PLA Filements, 1.75mm Filement, 3D Stereo Drawing Pen, Ideal Childrens Gift 8+ (Purple)

Tip:Please Remove the filament after using to prevent blockages.

Specifications:

✔Extrusion Mode: Melting

✔Width of Extrusion: Manual

✔Material Used: ABS PLA

✔Diameter of Material: 1.75mm

✔Speed of Extrusion: adjustable

✔Nozzle Hole Size: 0.7mm

✔Theological Extrusion Quantity: 0.076-0.86 m^2 per minute. Adjustable

✔Melting Temp of Material: ABS-230C PLA-170C

✔Adapter Current: 100/250V 3A

✔Pen Electric Spec: DC 12V 2A 24W

✔Pen Size: 184mm*31mm*46mm

Package Includes:

✔1x 3D Printing Pen

✔1x 12V 2A Power Adapter

✔3x 1.75mm ABS Filament with different colours, colours may vary

✔3x 1.75mm PLA Filament with different colours, colours may vary

✔1x Stand

✔1x User Manual

Safety and Warning Instruction:

✔The 3D printing pen is suitable for children 8+ some adult supervision maybe required

✔Please beware that the nib does get hot so mind you do not touch it with your hand while in operation

The 3d pen has a safety cutout after 5min of inactivity it will cutout and go into standby mode.

Product Features

  • SIMPLE AND PRACTICAL – This pen has a nice shape and isn’t too bulky it is a light to hold and ideal for adults or young children 8 years or older. (Easy to handle) you can design, draw on paper or in thin air, or trace and connect to create 3D masterpieces.
  • PERFECT GIFTS FOR YOUNG CHILDREN & ADULTS – 3D printing pen is a great gift and can bring you so much fun, and it is a very meaningful gift, no matter for who or what occasion. The 3D printing pen is ideal for children to develop their creativity skills From DIY toys to decorative items; anything within your imagination can be possible!
  • EASY TO USE – The pen is very user-friendly and if you have trouble there is a detail instruction manual. It works great, very easy to adjust the temperature. It does have a learning curve to get the hang of it and a younger child may need some adult supervision at first uses.
  • WHAT CAN YOU USE IT FOR- Education; Prototyping & Invention; Tactile Learning; Arts & Design; Spatial Thinking; Great tools for teaching and learning, this 3D printing pen can help Children to improve their spatial thinking ability, to encourage Children’s’ creative imaginations.
  • SAFE DESIGN & INTELLIGENT STANDBY FUNCTIO – The product will automatically switch to standby mode in 5 minutes, to avoid the risk of forgetting turning off the power, intelligent standby function allows you not to worry if you have left the 3d pen on.

Click Here If You Need More Detailed Info…

Quimat 3D Printer Controller Kit for Arduino Mega 2560 Uno R3 Starter Kits +RAMPS 1.4 + 5pcs A4988 Stepper Motor Driver + LCD 12864 for Arduino Reprap

Features:

(1) Mega 2560 R3

(2) 3D Printer Controller RAMPS 1.4
It is designed to fit the entire electronics needed for a RepRap in one small package for low cost.

RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion.
The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion.

(3) A4988 Stepper Motor Driver 

A4988 is a complete micro-stepping motor driver with built-in translator for easy operation 

(4) LCD 12864 Graphic Smart Display Controller

This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display.
You can easy connect it to your Ramps board using the “smart adapter” included. 

Package List:

(1) RAMPS 1.4 x 1 
(2) Mega 2560 R3 x 1 
(3) A4988 Stepper Motor Driver with Heatsink x 5 
(4) LCD 12864 Graphic Smart Display Controller x 1 
(5) Smart Adapter x 1 
(6) Cable x 2 
(7) USB Cable x 1

Product Features

  • 3D Printer Controller Kit Mega 2560 R3
  • 3D Printer Controller RAMPS 1.4,A4988 Stepper Motor Driver
  • LCD 12864 Graphic Smart Display Controller
  • 3D Printer Controller 100% compatible with Arduino RepRap
  • Detailed tutorials including project introduction and source code CAN BE PROVIDED FOR FREE,contact us BY Email to get documents

Visit The Website For More Information…