Kuman Mechanical Endstop Limit Switch with Cable For 3D Printer RepRap Prusa Mendel CNC for Arduino Mega 2560 RAMPS 1.4(Pack of 6) KB01

Mechanical Endstop kit is for RepRap 3D Printers or CNC machines. Mechanical Endstop is supported by RepRap electronics, RAMPS 1.4 and by other popular RepRap boards.

Customized high quality connection, using 22AWG wire, copper wire inside is very thick, can be resistant to current 2A, 300V voltage. An insulating layer over a wide range of temperatures, up to 80 degrees. Is the common connection of thin copper wire can not match. Not easy to pull off, plug it convenient, for ease of use, plug the other side to do the one, you can use the direct plug.

Connection Description:
Red line connecting VCC (ramps of +)
Connect the black wire GND (ramps of -)
Green Line connection SIGNAL (ramps in s)
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.
Pros: Easy to install, the more common styles
Length of Cable: 70 cm
Size: 32 x 10mm
Quantity: 6 set

Package include:
6 x Mechanical Switch Endstop
6 x 3Pin 70cm Cable

Product Features

  • High quality switching element
  • Customized high quality connection, using 22AWG wire, the copper wire inside is thick which can withstand 2A current, 300V voltage
  • Wide insulation temperature range: The insulation temperature can reach 80 degrees, however the ordinary thin copper wire can not
  • The wire is strong and not easy to pull off
  • Easy to use: the other side of the plug to do a whole, can be inserted directly to use.

Click Here If You Need More Detailed Info…

WINGONEER 3D Printer Controller Kit Ramps 1.4 + Full Graphic Smart Display Controller + Mega2560 + A4988 Stepper Motor Driver for RepRap (12864 LCD Full Graphic Smart Display Controller)

WINGONEER® trademark Reg.NO:012678447

Description:
This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the “smart adapter” included.After connecting this panel to your Ramps you don’t need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card.

Specifications:
Using a large screen 12864LCD(3.2″), it can support 8 GB;
With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing
Product comes encoder parameter adjustment can be achieved, and the file selection print!
Plug and play on the RAMPS, but need to modify the firmware to support.

Package include:
1x 12864 LCD controller(SD card not included)
1x Connector
2x 30 cm cable

Product Features

  • Support 8 GB
  • It contains a SD-Card reader and an rotary encoder
  • Graphic Smart Controller with 128 x 64 dot matrix LCD 12864 display
  • Easy to connect to Ramps board with the included smart adapter
  • With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing

Click Here If You Need More Detailed Info…

OSOYOO LCD 12864 Graphic Smart Display Controller module with connector adapter & cable for RepRap RAMPS 1.4 3D Printer kit Arduino Mega 2560 R3 Shield

Descriptions:

This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the “smart adapter” included.After connecting this panel to your Ramps you don’t need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card.

Specifications:

Using a large screen 12864LCD(3.2″), it can support 8 GB;

With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing

Product comes encoder parameter adjustment can be achieved, and the file selection print!

Plug and play on the RAMPS, but need to modify the firmware to support.

Package include:

1x 12864 LCD controller(SD card not included)

1x Connector

2x 30 cm cable

Product Features

  • Using a large screen 12864 LCD.
  • With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing.
  • Product comes encoder parameter adjustment can be achieved, and the file selection print.
  • Plug and play on the RAMPS, but need to modify the firmware to support.

Click Here If You Need More Detailed Info…

BIQU Equipment Optical Endstop with Cable Control Limit Switch for 3D Printer RepRap RAMPS 1.4(Pack of 3pcs) (Optical Endstop)

Package Included:
1*Optical Endstop
1*Connected Cable with 3 Pins 50cm Length

Product Features

  • Optical limiting optical switch 3D printer switch transmission
  • Supporting the use of RAMPS 1.4 plate
  • The optical endstop is a reliable endstop / switch solution for any type of 3D printers and other CNC and/ or 3D tools.
  • Module Function : Converter
  • Accessories Function : Connector

Detailed Information available on our Homepage…