PChero 5pcs E3D V6 Aluminum Extruder Hotend Nozzle Throat Heater Block with 10pcs 2mm Thick Heat-Insulated Cotton, for Makerbot 3D Printer

The key parts of the 3D printer – Heated aluminum block insulation, the benefit is the internal temperature changes gently, while saving power, to achieve energy saving effect.

Specification:
Compatibility:for E3D V6 Makerbot 3D Printer
Heater block Dimension: 20*15*11 mm, net weight: 8g/pc
Material: Aluminum
Inner hole for set screw: M6 and M3
Heater Mounting Hole: 6mm diameter
Thermocouple Mounting Holes:3mm diameter
Heat insulation cotton Dimension: 72*21*2 mm

Package Included:
5 x Aluminum Heater Block
10 x 3D printer heating block cottons

Note:
1. The heat insulation cotton Does Not have the pre-punched holes, it’s easy to bore a hole.

Product Features

  • Package Included: 5 x Aluminum Heater Block + 10 x 2mm thick Heat Insulation Cotton.
  • HEATER BLOCK – Made of durable Aluminum, Measures 20*15*11mm, Inner hole for set screw: M6 and M3 (heat pipe and thermocouple).
  • Heating Block Cotton – High temperature-resistant cotton can work for a long time at 900 degrees, 2mm thick heating block cotton For 3D printer hotend nozzle heat insulation.
  • Compatibility – Heating Aluminum Block for E3D V6 Makerbot 3D Printer structure, works with extruder nozzle throat & heat-insulated cotton.
  • Heater Mounting Hole: 6mm diameter, Thermocouple Mounting Holes:3mm diameter.

Visit The Website For More Information…

PChero 3D Printer Hot End 12V 40W Assembled Extruder Kits with 0.4mm Nozzle 1.75mm Filament for MK8

NTC 3950 Thermistor parameters:
– Small Size: 1.25mmx2.0mm glass bead
– High accuracy: 1%
– Resistance value at 25C=100K
– Wiring insulation: high temperature teflon/PTFE
– Wiring length: 1 meter

Specification of Cartridge Heater:
Voltage: 12v, Power: 40w
Material: 304 Stainless Steel
Wire Length :1m
Diameter: 6mm
Length: 20mm

Specification of Extruder Tube:
Type : Nozzle Throat
Compatibility : 3D Printer
Outer Thread : M6
Inner Diameter : 2mm
Length : 30mm
Filament Diameter : 1.75mm
Material : Stainless Steel

Specification of Brass Nozzle:
Type :0.4mm Extruder Brass Nozzle Print Head
Color: Golden.
Material: brass.
Size: 5*13mm.
Input Diameter: 1.75mm.
Output Diameter: 0.4mm.
Compatible: compatible with all 1.75mm PLA ABS printer.

Package Including:
1 x MK8 Nozzle 0.4mm extrusion diameter.
1 x Stainless PTFE lined barrel.
1 x Aluminum heater block with 1 x M3x3 setscrew, 1 x M3x4 Socket head screw, 1 x M3 Washer.
1 x 12V 40W Cartridge Heater.
1 x NTC 3950 Pre-wired thermistor

Product Features

  • Cartridge heaters is consist of a cylindrical stainless steel tube and thus provide a high corrosion prevention. With100Kohm NTC 3950 Thermistors / temperture sensor.
  • HEATER BLOCK – Made of durable Aluminum, Measures 20*20*10mm, Inner hole for set screw: M6 and M3 (heat pipe and thermocouple).
  • Nozzle Throat: Outer Thread – M6; Inner Diameter – 2mm; Length – 30mm; Filament Diameter – 1.75mm; Material – Stainless Steel.
  • 0.4mm Extruder Brass Nozzle Print Head: Color – Golden; Material – copper (brass); Size – 5*13mm; Input Diameter: 1.75mm; Output Diameter: 0.4mm.
  • Compatible: compatible with MK8 3D printer. Attention: Small parts, keep away from children!!!

Visit The Website For More Information…

PChero Hot Bed Power Expansion Board MOS Tube High Current Load Module for 3D Printer

Specifications:

Item Dimension: 50*60mm/ 2.36*1.97 inch
Mounting holes: 3.5mm diameter
Color: black, cable length: 6 inch
Max Current: 25A (Enhance heat dissipation) safe for prolonged times. ensure active cooling of the heatsink.

Package Included:

1 x Heat bed Power Module
1 x Connection cable for input signal

Note:

1. Please double-confirm the wire you connect is right when installing this MOSFET Board, if you have any issue please contact us firstly, thanks!
2. Please make sure the maximum current load does Not Exceed 25Amps, to ensure a steady & Safe work.

Product Features

  • General add-on heated bed power expansion module, compatible with Anet A8 and most 3d printers. Effective to resolve the hot bed power is too large and the load current problems.
  • EQUIPPED with 32 bit high-speed ARM chip, the heat bed power module can be used in both Chitu motherboard and other open 3D printer motherboards.
  • If you intend to use heated bed with your 3D printer that uses a 12V power supply, then this PChero heat bed module is recommended.
  • OFFER PROTECTION- With this add-on module to your controller board, you can lead the maximum current up to 25A. If you need anything greater or equal to 15A this module is a must!
  • NOTE: Under the premise of normal cooling, it works stably under I(Max)=25A, the current must NOT exceed 25A while in the work process.

Click Here For More Information

PChero 5pcs Aluminum Extruder Hotend Nozzle Throat Heater Block with 10pcs 2mm Thick Heat-Insulated Cotton, for MK7 MK8 Makerbot 3D Printer

The key parts of the 3D printer – Heated aluminum block insulation, the benefit is the internal temperature changes gently, while saving power, to achieve energy saving effect.

Specification:

Heater block Dimension: 20*20*10 mm, net weight: 7g/pc
Material: Aluminum
Inner hole for set screw: M6 and M3
Heater Mounting Hole: 6mm diameter
Thermocouple Mounting Holes:3mm diameter
Heat insulation cotton Dimension: 72*21*2 mm

Package Included:

5 x Aluminum Heater Block
10 x 3D printer heating block cottons

Note:

1. The heat insulation cotton Does Not have the pre-punched holes, it’s easy to bore a hole.

Product Features

  • Package Included: 5 x Aluminum Heater Block + 10 x 2mm thick Heat Insulation Cotton.
  • HEATER BLOCK – Made of durable Aluminum, Measures 20*20*10mm, Inner hole for set screw: M6 and M3 (heat pipe and thermocouple).
  • Heating Block Cotton – High temperature-resistant cotton can work for a long time at 900 degrees, 2mm thick heating block cotton For 3D printer hotend nozzle heat insulation.
  • Compatibility – Heating Aluminum Block for MK7 MK8 Makerbot 3D Printer structure, works with extruder nozzle throat & heat-insulated cotton.
  • Heater Mounting Hole: 6mm diameter, Thermocouple Mounting Holes:3mm diameter.

Visit The Website For More Information…