Kuman Mechanical Endstop Limit Switch with Cable For 3D Printer RepRap Prusa Mendel CNC for Arduino Mega 2560 RAMPS 1.4(Pack of 6) KB01

Mechanical Endstop kit is for RepRap 3D Printers or CNC machines. Mechanical Endstop is supported by RepRap electronics, RAMPS 1.4 and by other popular RepRap boards.

Customized high quality connection, using 22AWG wire, copper wire inside is very thick, can be resistant to current 2A, 300V voltage. An insulating layer over a wide range of temperatures, up to 80 degrees. Is the common connection of thin copper wire can not match. Not easy to pull off, plug it convenient, for ease of use, plug the other side to do the one, you can use the direct plug.

Connection Description:
Red line connecting VCC (ramps of +)
Connect the black wire GND (ramps of -)
Green Line connection SIGNAL (ramps in s)
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.
Pros: Easy to install, the more common styles
Length of Cable: 70 cm
Size: 32 x 10mm
Quantity: 6 set

Package include:
6 x Mechanical Switch Endstop
6 x 3Pin 70cm Cable

Product Features

  • High quality switching element
  • Customized high quality connection, using 22AWG wire, the copper wire inside is thick which can withstand 2A current, 300V voltage
  • Wide insulation temperature range: The insulation temperature can reach 80 degrees, however the ordinary thin copper wire can not
  • The wire is strong and not easy to pull off
  • Easy to use: the other side of the plug to do a whole, can be inserted directly to use.

Click Here If You Need More Detailed Info…

3D Printer ANYCUBIC TriGorilla Integrated Main board Compatible Mega2560 & RAMPS1.4 Combo Control Board 4 Layers PCB Controller Board for RepRap Mendel Prusa I3

Description
TriGorilla is a integrated main board that is integrated with the mighty function of the Mega2560+ramps 1.4 on respect of both software and hardware and has more premium features; the streamlined interfaces effectively avoid the unnecessary troubles and power than Ramps 1.4 + Mega2560, it is a feature rich all-in-one electronics solution for Reprap Mendel Prusa and other CNC devices.

Parameter
Main Control Chip:ATMEGA256016AU
Input Power: 10V ~ 30V
Standby Current: 35 mA ± 5 mA
Stepper Motor Drivers: 5 Kanal max
Hot bed Output Control: 1 Kanal
Heated output control: 2 Kanäle
under-current output control: 3 Kanäle
Dimensions: 125 mm x 82 mm

Product Features

  • Simple to install: Integrated with the mighty function of the Mega2560+ramps 1.4 kit, Great reduce the wiring problem, more convenient connection, and more stable.(widely used in 3D printers, e.g. Kossel, Prusa i3, corexy, etc
  • Excellent compatibility: Firmware can use the same configuration as ramps1.4, the marlin firmware which runs in Mega2560+ramps 1.4 kits can directly running in TriGorilla board.TriGorilla had reserved SERVO, UART, IIC expansion, so you can use it realize automatic leveling, control touch screen smart controller, control wireless module and the detection of break, etc
  • voltage input at super wide range, short-circuit protection: TriGorilla adopts DC – DC step-down scheme design and Recoverable fuse for short-circuit protection, improving the MEGA2560 board serious heating problem, Allowing any power supply from 10V-30V.
  • Support up to 5 motor drivers, support A4988/ DRV8825 /TMC2100 driver: Motor drive circuit doesn’t integration on the circuit board. You can change any stepper motor driver you need, easier to operate. (Support A4988/ DRV8825 /TMC2100 driver)
  • Convenient to use: TriGorilla motherboard support LCD2004 and LCD12864 without using adapter, and there are two choices for board power supply, you can choose DC power supply connection or directly from the terminal.

Click Here If You Need More Detailed Info…

3D Printer Cooling Fan 12V DC 30x30x10 mm – 1m for E3D V6 Hotend – RepRap Mendel Prusa i3

The standard 12v DC fan for use with any E3D HotEnd or for general cooling needs.

Product Features

  • The standard 12v DC fan for use with any E3D HotEnd including the Prusa i3 Mk2 or for general cooling needs.
  • This is a high-speed fan with a high quality 2 ball bearing.
  • 12 Volts DC
  • Size: 30x30x10mm Lead length: 1m
  • Air Flow 4.1 cfm

Detailed Information available on our Homepage…

Zomiee 12V 40W Ceramic Cartridge Heater for 3D Printer Reprap Prusa Mendel (pack of 6 pcs)

Specifications:
Voltage: 12V
Electricity: 40W
Diameter: 6mm
Tube length: 15mm
Line length: 1M
Size: ?6*20mm
Name: Cartridge Heater
Material: Stainless steel 304
Cartridge Heater for 3D Printer
100% Brand new and high quality

Package:
6 X 12V Cartridge Heater for 3D Printer

Product Features

  • Widely Application–The Cartridge Heater can work in the heating medium of the connection on both ends,which is widely applied in mould heating, hot core box, shoot core machine and other dielectric heating equipment.
  • High temperature, more durable, fast thermal, more secure.
  • 100% Brand new and high quality.
  • Cartridge Heater for 3D Printer.
  • Resistance: 2080 high temperature high quality oxidation powder.

Detailed Information available on our Homepage…