3D Printer Kit with Mega 2560 Board + RAMPS 1.4 Controller + 5pcs A4988 Stepper Motor Driver with Heatsink + LCD 12864 Graphic Smart Display Controller with Adapter for 3D Printer

Features:
Brilliant 3D Printer Accessories Set meets most needs.
Including RAMPS 1.4 Board, LCD12864, Arduino-Compatible Mega 2560 R3, A4988 StepStick Stepper Motor Module, and other accessories.

12864 LCD Controller:
This Full Graphic Smart Controller Contains a SD-Card Reader, an Rotary Encoder and a 128 x 64 Dot Matrix LCD Display.
You can easy Connect it to your Ramps Board using the “Smart Adapter” included.
After Connecting this Panel to your Ramps you don’t need your pc any more, the Smart Controller Supplies Power for your SD card.
Further more all Actions like Calibration, Axes Movements can be Done by just using the Rotary Encoder on the Smart Controller.
Print your 3D Designs without PC, just with a G-Code Design Stored on the SD Card.

RAMPS 1.4:
Fully Assembled & Tested, No Soldering Required.
The Modular Design includes Plug in Stepper Drivers and Extruder Control Electronics on an Arduino MEGA Shield
For Easy Service, Part Replacement, Upgrade-Ability and Expansion.

Mega 2560 R3 Board:
Microcontroller: ATMEGA2560-16AU
Operating Voltage: 5V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 6-20V
Digital I/O Pins: 54 (of which 15 provide PWM output)
Analog Input Pins: 16
DC Current per I/O Pin: 40 mA
DC Current for 3.3V Pin: 50 mA
Flash Memory: 256 KB of which 8 KB used by bootloader
SRAM: 8 KB
EEPROM: 4 KB
Clock Speed: 16 MHz

A4988 Stepper Motor Driver Package Includes: 1 x 3D Printer Controller RAMPS 1.4 Board
1 x LCD12864 Intelligent controller
1 x Arduino-Compatible Mega 2560 R3
5 x A4988 StepStick Stepper Motor Driver Module with Heatsink
1 x Adapter
2 x FC flat cable
1 x USB Cable

Product Features

  • Brilliant 3D Printer Accessories Set meets most needs. Including RAMPS 1.4 Board, LCD12864, Arduino-Compatible Mega 2560 R3, A4988 StepStick Stepper Motor Module, and other accessories.
  • This full graphic Smart LCD12864 Intelligent controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display.
  • RAMPS (RepRap Arduino-compatible MEGA Pololu Shield) is designed to fit the entire electronics needed for a RepRap in one small controller for a lower cost and a smaller size.
  • Arduino-Compatible Mega 2560 R3 is fully compatible with the original Arduino MEGA 2560 R3, able to use all the Arduino open source platform to create or learn interactive objects.
  • A4988 StepStick Module is a complete microstepping motor driver with built-in translator for easy operation.

Click Here If You Need More Detailed Info…

TRIGORILLA ANYCUBIC I3 Mega 3D Printer All Metal Printing with Patented Ultrabase Heated Bed for 1.75mm Filament PLA/ABS/HIPS/Wood

Trigorilla ANYCUBID i3 Mega Advantage:

【1】Filament Sensor: A built-in sensor recognizes low filament levels and will pause printing in progress until filament is reloaded.
【2】Comes with Cura as the slicer to convert your STL files to Gcode for use with this printer. Easy for you to start your printing.
【3】TFT Touch Screen: 3.5″ touch screen gives you easy operation and instant previews of 3D model files.
【4】Updated Structure: Full metal structure and dual Z axis make it more stable, higher precision and quieter when printer
【5】Over 24 hours testing before shipping and one year warranty.
【6】Good printing quality, high precious printer and reasonable cost for the beginners and good performance for the enthusiasts.

PRINTING:

Modeling Technology:FDM (Fused Deposition Modeling)
Positioning Accuracy: X/Y 0.125mm,Z 0.002mm
Printing Size: 210 x 210 x 205 mm
Machine Size: 405x410x453 mm
Gross weight: ~11 kg
Printing Speed: 20~100mm/s
Traveling Speed:100mm/s
Filament:1.75mm PLA,ABS,HIPS,WOOD
Layer Thickness:0.05-0.3mm
Nozzle diameter:0.4mm

Electrical:

Input:AC 100-220V 50-60Hz
Working Voltage: 12V DC

Software:

Slice Software: Cura
Software Input Formats:STL,OBJ,DAE,AMF
Software output Formats: GCode
Working Mode:Online or SD offline

Temperature:

Max Nozzle Temperature:260℃
Max Hot bed Temperature:110℃
Ambient Operating Temperature: 8℃-40℃

NOTE:

Every 3D printer would be trough over 24 hours testing before the shipping. There may exist some marks on the platform after testing. Please use the soft cloth with alcohol to clean it.

Product Features

  • 【Resume Printing】: It could resume printing from where the last print was stopped due to power failure
  • 【3 Steps Fast Assembly】: You just need to install 8 screws and connect 3 wires before the first printer and then start your printing on the 3.5-inch TFT touch screen
  • 【Patented Heated Bed】: ANYCUBIC Ultrabase with strong adhesion and the smoothly lattice bottom surface, easier to take off model by hands
  • 【High cost-effective FDM 3D Printer Kit】: Including 3D printers, CD cards, printing supplies, USB data cables, power cords, tool kits, hanging posts, user guides, etc.
  • 【NOTE】: Large Building Size: 210 x 210 x 205mm. We offer 100% original ANYCUBIC 3D Printer professional after sales technical support.

Click Here For More Information

WINSINN 3D Printer Controller Kit For Arduino Mega 2560 Uno R3 Starter Kits + RAMPS 1.6 Upgraded Mosfet + 5Pcs DRV8825 Stepper Motor Driver + LCD 12864 for Arduino Reprap


Ramps 1.6 board:

-Ramps 1.6 is optimized and launched based on Ramps 1.4 & Ramps 1.5. The Struture almost same as Ramps 1.5 , the difference is Ramps 1.6 have new 2pin connectors,which more simple and convenient to connect,also will not be burnt easily. And Ramps 1.6 have a good Heatsink above MOS tube in order to give a better function to heat dissipation. Beside, the Power of Ramps 1.6 is more larger than Ramps 1.5, the largest power will be up to or 270W, and Ramps 1.5 just can be up to 200W, or smaller than 200W.

DRV8825 Driver:

-Suitable for driving below 8.2V ~ 45V 2.5A stepper motor
-Six different stepping resolutions: full, half, 1/4,1/8,1/16,1/32
-Adjustable potentiometer can adjust the maximum output current, resulting in higher step rate
-Automatic current decay mode detection / selection
-Thermal shutdown circuit, undervoltage lockout, crossover current protection
-Ground short-circuit protection and load short-circuit protection

Mega 2560 R3:

-Operating Voltage: 5V
-Input Voltage (recommended):7-12V
-Input Voltage (limits):6-20V
-Digital I/O Pins:54 (of which 14 provide PWM output)
-Analog Input Pins:16
-DC Current per I/O Pin:40 mA
-DC Current for 3.3V Pin:50 mA
-Flash Memory:256 KB of which 4 KB used by bootloader
-SRAM:8 KB
-EEPROM:4 KB

—————————————————————————————————————

Package include:
►1 x RAMPS 1.6 Board
►1 x Mega 2560 R3 Board
►1 x 12864 LCD Display Controller
►1 x LCD Smart Adapter
►5 x DRV8825 Stepper

———————————————————————————————————————

►Note:
►We offer the best products and services, if there has any problems, you can tell us anytime. Thank you:))

Product Features

  • ✔️DRV8825 driver board widely used in 3D printers and small CNC machines. It is upgrade of A4988, 4-layer PCB for improved heat dissipation and decrease chip resistance. It suitable for driving below 8.2V ~ 45V 2.5A stepper motor, And had Six different stepping resolutions: full, half, 1/4 ,1/8, 1/16, 1/32.
  • ✔️12864 LCD: The intelligent controller includes an SD card reader, rotary encoders and a 20-character × 4 line LCD display. You can easily connect it to your RAMPS 1.6 board using “smart adapter” included. This panel connect your RAMPS 1.6, you do not need your computer, your SD card intelligent controller power supply. All further operations, such as calibration, the axis movement can be done only with a rotary encoder intelligent controller.
  • ✔️This kit includes a complete set of the most common and useful components that can be used by all tech-savvy people out there to build their own printer controller. A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • ✔️Product Warranty: WINSINN are devoted to offer premium quality products to all cherished customers. Meanwhile supply 60 days money back guarantee and 24 months warranty. If there are any questions, please feel free to contact us, WINSINN Customer Service Team will spare no efforts to assist with you within 24 hours.
  • ✔️Ramps 1.6 is optimized and launched based on Ramps 1.4 & Ramps 1.5. The Struture almost same as Ramps 1.5 , the difference is Ramps 1.6 have new 2pin connectors,which more simple and convenient to connect,also will not be burnt easily. And Ramps 1.6 have a good Heatsink above MOS tube in order to give a better function to heat dissipation. Beside, the Power of Ramps 1.6 is more larger than Ramps 1.5, the largest power will be up to or 270W, and Ramps 1.5 just can be samller than 200W.

Click Here If You Need More Detailed Info…

FYSETC 3D Printer Heated bed Silicone leveling, Column OD 0.63 in ID 0.16 in Stable Hot Bed Tool Heat-resistant Silicone Buffer for Anet A8 Wanhao D9 Anycubic Mega, 4 Pcs black

FYSETC is focus on 3D Printing Accessories, offers a variety of quality 3D Printing parts. We are constantly improving its products to deliver the best experience to each customer.

These silicone buffers serve to replace on your heating bed original springs. It is stable and does not shake when used, better to keep your 3D printer leveled.

Model: 4 high silicone leveling column -black
Feature: Assist 3d printer leveling
Material: Silicone
Silicone: Heat-resistant and pressure-resistant
Diameter: OD 0.63″(16mm) ID 0.16″(4mm)
Height: High 0.71″(18mm)
Package Includes:
4x high silicone leveling column- black

Product Features

  • For 3D Printer Hot Bed/ Platform, bottom connect, can replace original spring leveling.
  • New upgraded 3d printing leveling tool, Special design for Anet A8 Wanhao D9 Anycubic Mega i3 and most heated bed.
  • This heat-resistant and pressure-resistant silicone leveling column with a 4mm inner diameter makes it better to level your 3D printer.
  • The silicone buffers are simply installed instead of the original spring and it is no longer possible movement, your set levels remain!
  • After Sales Guarantee: each one defective item can have the free replace or refund, need more help please feel free to email or Q&A us, we will try our best to service you.

Detailed Information available on our Homepage…