3D Printer Kit with Mega 2560 Board + RAMPS 1.4 Controller + 5pcs A4988 Stepper Motor Driver with Heatsink + LCD 12864 Graphic Smart Display Controller with Adapter for 3D Printer

Features:
Brilliant 3D Printer Accessories Set meets most needs.
Including RAMPS 1.4 Board, LCD12864, Arduino-Compatible Mega 2560 R3, A4988 StepStick Stepper Motor Module, and other accessories.

12864 LCD Controller:
This Full Graphic Smart Controller Contains a SD-Card Reader, an Rotary Encoder and a 128 x 64 Dot Matrix LCD Display.
You can easy Connect it to your Ramps Board using the “Smart Adapter” included.
After Connecting this Panel to your Ramps you don’t need your pc any more, the Smart Controller Supplies Power for your SD card.
Further more all Actions like Calibration, Axes Movements can be Done by just using the Rotary Encoder on the Smart Controller.
Print your 3D Designs without PC, just with a G-Code Design Stored on the SD Card.

RAMPS 1.4:
Fully Assembled & Tested, No Soldering Required.
The Modular Design includes Plug in Stepper Drivers and Extruder Control Electronics on an Arduino MEGA Shield
For Easy Service, Part Replacement, Upgrade-Ability and Expansion.

Mega 2560 R3 Board:
Microcontroller: ATMEGA2560-16AU
Operating Voltage: 5V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 6-20V
Digital I/O Pins: 54 (of which 15 provide PWM output)
Analog Input Pins: 16
DC Current per I/O Pin: 40 mA
DC Current for 3.3V Pin: 50 mA
Flash Memory: 256 KB of which 8 KB used by bootloader
SRAM: 8 KB
EEPROM: 4 KB
Clock Speed: 16 MHz

A4988 Stepper Motor Driver Package Includes: 1 x 3D Printer Controller RAMPS 1.4 Board
1 x LCD12864 Intelligent controller
1 x Arduino-Compatible Mega 2560 R3
5 x A4988 StepStick Stepper Motor Driver Module with Heatsink
1 x Adapter
2 x FC flat cable
1 x USB Cable

Product Features

  • Brilliant 3D Printer Accessories Set meets most needs. Including RAMPS 1.4 Board, LCD12864, Arduino-Compatible Mega 2560 R3, A4988 StepStick Stepper Motor Module, and other accessories.
  • This full graphic Smart LCD12864 Intelligent controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display.
  • RAMPS (RepRap Arduino-compatible MEGA Pololu Shield) is designed to fit the entire electronics needed for a RepRap in one small controller for a lower cost and a smaller size.
  • Arduino-Compatible Mega 2560 R3 is fully compatible with the original Arduino MEGA 2560 R3, able to use all the Arduino open source platform to create or learn interactive objects.
  • A4988 StepStick Module is a complete microstepping motor driver with built-in translator for easy operation.

Click Here If You Need More Detailed Info…

gazechimp 3D Printer Motherboard Parts kit for Reprap Mini-Rambo 1.3+2004A W/LCD Screen Display Controller and Adapter

Description:

– 3D Printer Accessories for Reprap Mini-Rambo 1.3+2004A LCD Display,

– 4 x integrated microstep motor controllers 1/16,4 MOSFET PWM outputs,3 thermistor inputs.

– Current control of the PWM motor (without small knobs).

– SMPS supports the maintenance-free printing of 10-28 V DC power supply.

– 2 protected power fuse (heated bed, 15a 10-35 V, 10a 10-28 V primary power:

– Motors (dedicated 5a fuse) + extruders, fans and logic (dedicated 5a fuse), lufa USB.

Specification:

– Material: PCB Plastic

– Size:105x70mm

Package Includes:

1 x Mini-Rambo 1.3 motherboard

1 x USB cable

4 x heat sink

2 x terminal

1 x 2004 display

2 x gray cable

Product Features

  • 3D Printer Accessories for Reprap Mini-Rambo 1.3+2004A LCD Display,
  • 4 x integrated microstep motor controllers 1/16,4 MOSFET PWM outputs,3 thermistor inputs.
  • Current control of the PWM motor (without small knobs).
  • SMPS supports the maintenance-free printing of 10-28 V DC power supply.
  • 2 protected power fuse (heated bed, 15a 10-35 V, 10a 10-28 V primary power:

Visit The Website For More Information…

WINSINN 3D Printer Controller Kit For Arduino Mega 2560 Uno R3 Starter Kits + RAMPS 1.6 Upgraded Mosfet + 5Pcs DRV8825 Stepper Motor Driver + LCD 12864 for Arduino Reprap


Ramps 1.6 board:

-Ramps 1.6 is optimized and launched based on Ramps 1.4 & Ramps 1.5. The Struture almost same as Ramps 1.5 , the difference is Ramps 1.6 have new 2pin connectors,which more simple and convenient to connect,also will not be burnt easily. And Ramps 1.6 have a good Heatsink above MOS tube in order to give a better function to heat dissipation. Beside, the Power of Ramps 1.6 is more larger than Ramps 1.5, the largest power will be up to or 270W, and Ramps 1.5 just can be up to 200W, or smaller than 200W.

DRV8825 Driver:

-Suitable for driving below 8.2V ~ 45V 2.5A stepper motor
-Six different stepping resolutions: full, half, 1/4,1/8,1/16,1/32
-Adjustable potentiometer can adjust the maximum output current, resulting in higher step rate
-Automatic current decay mode detection / selection
-Thermal shutdown circuit, undervoltage lockout, crossover current protection
-Ground short-circuit protection and load short-circuit protection

Mega 2560 R3:

-Operating Voltage: 5V
-Input Voltage (recommended):7-12V
-Input Voltage (limits):6-20V
-Digital I/O Pins:54 (of which 14 provide PWM output)
-Analog Input Pins:16
-DC Current per I/O Pin:40 mA
-DC Current for 3.3V Pin:50 mA
-Flash Memory:256 KB of which 4 KB used by bootloader
-SRAM:8 KB
-EEPROM:4 KB

—————————————————————————————————————

Package include:
►1 x RAMPS 1.6 Board
►1 x Mega 2560 R3 Board
►1 x 12864 LCD Display Controller
►1 x LCD Smart Adapter
►5 x DRV8825 Stepper

———————————————————————————————————————

►Note:
►We offer the best products and services, if there has any problems, you can tell us anytime. Thank you:))

Product Features

  • ✔️DRV8825 driver board widely used in 3D printers and small CNC machines. It is upgrade of A4988, 4-layer PCB for improved heat dissipation and decrease chip resistance. It suitable for driving below 8.2V ~ 45V 2.5A stepper motor, And had Six different stepping resolutions: full, half, 1/4 ,1/8, 1/16, 1/32.
  • ✔️12864 LCD: The intelligent controller includes an SD card reader, rotary encoders and a 20-character × 4 line LCD display. You can easily connect it to your RAMPS 1.6 board using “smart adapter” included. This panel connect your RAMPS 1.6, you do not need your computer, your SD card intelligent controller power supply. All further operations, such as calibration, the axis movement can be done only with a rotary encoder intelligent controller.
  • ✔️This kit includes a complete set of the most common and useful components that can be used by all tech-savvy people out there to build their own printer controller. A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • ✔️Product Warranty: WINSINN are devoted to offer premium quality products to all cherished customers. Meanwhile supply 60 days money back guarantee and 24 months warranty. If there are any questions, please feel free to contact us, WINSINN Customer Service Team will spare no efforts to assist with you within 24 hours.
  • ✔️Ramps 1.6 is optimized and launched based on Ramps 1.4 & Ramps 1.5. The Struture almost same as Ramps 1.5 , the difference is Ramps 1.6 have new 2pin connectors,which more simple and convenient to connect,also will not be burnt easily. And Ramps 1.6 have a good Heatsink above MOS tube in order to give a better function to heat dissipation. Beside, the Power of Ramps 1.6 is more larger than Ramps 1.5, the largest power will be up to or 270W, and Ramps 1.5 just can be samller than 200W.

Click Here If You Need More Detailed Info…

Gaorunli Measurement and analysis tools 2004 LCD Screen Controller Display with Cable for Reprap Ramps 1.4 3D Printer Kit Accessory for Creality CR-10 Suitable for factories and other social areas

Features:

2004 LCD smart controller for 3D printer.

Supports for RAMPS 1.4 control board.

Clear white characters with blue backlit, displays 4 lines and 20 characters per line.

Supports for selecting the files to print.

Replacement screen for CR-10 3D Printer.

Specifications:

Screen: LCD2004

Suitable for: Creality CR-10

Item Size: 9.3 * 8.6 * 3cm/ 3.6 * 3.4 * 1.2in

Item Weight: 120g/ 4.3oz

Package List:

1 * Screen

Product Features

  • Especially perfect for model spraying, make up cosmetic, nail arts, airbrush DIY and design painting etc.
  • With oil/water separator for separating and releasing water.
  • It can start with pressure, and continuous work. Auto start and auto stop function.
  • Airbrush holder, Double-action Trigger Control.
  • Basic airbrush kit for every model DIY lovers, painting designers and make-up artist etc.

Click Here If You Need More Detailed Info…