TECNOIOT 3D Printer Kit for Arduino Mega 2560 R3 Development Board + RAMPAS 1.4 Controller + 5pcs DRV8825 Stepper Motor Module + 6pcs Endstop

Mega 2560: 

La junta de Mega 2560 es un microcontrolador basado en el Atmega2560. Tiene 54 pines digitales de entrada/salida (de los cuales 14 pueden usarse como salidas PWm), 16 entradas analógicas, 4 UART (puertos de serie de hardware), un oscilador de cristal de 16 Mhz, conexión USB, una entrada de alimentación, calentador ICSP y botón de reseteado.

Placa controladora RAMPS 1.4:
Salida de calentador/ventilador y tres circuitos termistores MOSFET.
Seguridad adicional FUSION 5 A y protección de componentes.
Fusible adicional de control de calefacción de 11 A.
Adecuado para placa de controlador paso a paso 5 Pololu.
Entrada de pin de placa de Pololu, fácil de reemplazar y quitar.
Pines I2C y SPI para uso prolongado; todos los MOSFET a pines PWM para proporcionar versatilidad.
Salida de corriente nominal: 3 A, LED indica cuando funciona el calentador.
DRV8825 Stepper Motor Driver: 
1)*Suitable for driving below 8.2V ~ 45V 2.5A stepper motor  
2)*Six different stepping resolutions: full, half, 1 / 4,1 / 8,1 / 16,1 / 32.  
3)*A simple steps and direction control interface.  
4)*Automatic current decay mode detection / selection.  
5)*Thermal shutdown circuit, undervoltage lockout, crossover current protection.  
6)*Ground short-circuit protection and load short-circuit protection.  

Endstop 
Línea roja conecta VCC (rampas de +)
Conecta el cable GND negro (rampas de -)
Señal de conexión de línea verde (rampas en s)

Package Contains:

1pc x MEGA 2560 R3
1pc x RAMPS 1.4 Control Panel
5pcs x DRV8825 Stepper Motor Driver Module
6pcs x Mechanical Endstop

Product Features

  • 【3D Printer】 All actions such as calibration, axis movements can be performed simply using the rotary encoder in the intelligent controller. Print your 3D designs without a PC, only with a G-Code design stored on the SD card
  • 【Ramps1.4】 RAMPS interconnects a Mega Arduino compatible with the powerful MEGA platform supported by Arduino and has plenty of room for expansion
  • 【MEGA2560】 The Mega 2560 is compatible with most of the shields designed for the Arduino Duemilanove, or Diecimilaa4988 is a complete Microstepping motor controller with integrated translator for easy handling. Mega 2560 R3, with this product, you can use the entire open source Arduino platform to create or learn interactive objects.
  • 【DRV8825】 DRV8825 is a complete microstepping motor controller with integrated translator for easy operation.DRV8825 is the upgrade of A4988, 4-layer PCB for improved heat dissipation and decrease chip resistance
  • 【Fast delivery】 Fast and high quality delivery of Spain buying in TECNOIOT

Click Here If You Need More Detailed Info…

SODIAL 5pcs 220x220mm Plastic 3D Printer Accessories Hot Bed Stickers For Wanhao i3 3D Printer Parts & Accessories

* SODIAL is a registered trademark. ONLY Authorized seller of SODIAL can sell under SODIAL listings.Our products will enhance your experience to unparalleled inspiration.
SODIAL(R) 5pcs 220x220mm Plastic 3D Printer Accessories Hot Bed Stickers For Wanhao i3 3D Printer Parts & Accessories
100% brand new and high quality.
Single sheet design installs more quickly and with fewer bubbles than tape or films
Build sheet adheres to a print bed to help the filament stick during printing, while also enabling clean removal of the printed part afterward.
Instant bonding with convenient use.
Background is made of adhesive, easily stick on the heat bed platform.
Material: Plastic
Color: Black + White
Size: 220x220mm
Shape: Rectangle
Package include:
5 x print stickers
Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.

Product Features

  • easy and convenient
  • Matte surface, nice
  • Surface scrub treatment, can be reused, paste the hot bed first, and then paste, can be attached to PLA, ABS, HIPS, PETG, TPE supplies, nylon, PC, RETT materials

Visit The Website For More Information…

prettygood7 5pcs 100cm 4 Pin Dupont Cable Female to Male Terminal Line 3D Printer Part


Features:
24AWG conductor is used to withstand 2A current and withstand 300V voltage.
The temperature range of the insulating layer can reach 80 degrees centigrade, and it is not easy to break and convenient to plug and pull.

Specifications:
Color: Random Color
Type: Dupont Cable
Connector: Male to Female
Pin Quantity: 4 Pin
Length: approx. 100cm/3.3ft
Quantity: 5pcs

Note:
Please allow 1-3 cm differs due to manual measurement.
Due to the different display and different light, the picture may not show the actual color of the item. Thanks for your understanding.
Package included:5 x Dupont Cables

Product Features

  • 24AWG conductor is used to withstand 2A current and withstand 300V voltage
  • The temperature range of the insulating layer can reach 80 degrees centigrade, and it is not easy to break and convenient to plug and pull.
  • Type: Dupont Cable
  • Connector: Male to Female
  • Length: approx. 100cm/3.3ft

Visit The Website For More Information…

SIQUK 10pcs 0.4MM Brass Extruder Nozzle Print Heads and 5pcs Cleaning Needles 0.4mm Drill Bits with 2M PTFE Teflon Tube for E3D V6 Makerbot 3D printer (Bonus: 5pcs Nozzle Throat)


SIQUK 3D Printer Tool Kit

Features/Specifications
Nozzle throat: material: stainless steel; outer thread: M6; inner diameter: 2mm; length: 22.5mm; filament diameter: 1.75mm
Extruder brass nozzle: material: copper(brass); size: 5*13mm; output diameter: 0.4mm; input diameter: 1.75mm; color: golden
PTFE teflon tube: material: PTFE(Poly Tetra Fluoro Ethylene); length: 2m; outside diameter: 4mm; inside diameter: 2mm; density: 2.15-2.20g/cm3
Cleaning Needles Drill Bit: material: stainless steel; bit diameter: 0.4mm

Compatibility
Compatible with all 1.75mm E3D V6 Makerbot 3D printer. 

Note: these 3D printer heads are small parts, please keep them away from children to avoid swallow risk.

package including:
10 x 3D Printer extruder brass nozzle 
5 x 3D Printer nozzle throat 
5 x cleaning Needles drill bits
1 x 2M PTFE teflon tube(2.0mm ID/4.0mm OD) 

Product Warranty

SIQUK are devoted to offer premium quality products to all cherished customers. Meanwhile supply 45 days money back guarantee and 18 months warranty.

If there are any questions, please feel free to contact us, SIQUK Direct Customer Service Team will spare no efforts to assist with you within 24 hours.

Product Features

  • Compatibility: compatible with all 1.75mm E3D V6 Makerbot 3D printer
  • Nozzle throat: material: stainless steel; outer thread: M6; inner diameter: 2mm; length: 22.5mm; filament diameter: 1.75mm
  • Extruder brass nozzle: material: copper(brass); size: 5*13mm; output diameter: 0.4mm; input diameter: 1.75mm; color:golden
  • PTFE teflon tube: material: PTFE(Poly Tetra Fluoro Ethylene); length: 2m; outside diameter: 4mm; inside diameter: 2mm; density: 2.15-2.20g/cm3
  • Cleaning Needles Drill Bit: material: stainless steel; bit diameter: 0.4mm

Click Here If You Need More Detailed Info…